Engl Steve Morse Signature 100 Betreibershandbuch PDF herunterladen (Seite 18)

Switch no. 44 lets you activate the amp's power supply if you have an ENGL

connected to this port.

Before you connect any other MIDI footswitch or effects device, always

make sure that switch no. 44 is set to the right to avoid damaging the device.

This selector activates a MIDI In port power supply for connected ENGL MIDI foot

boards. Power is fed to the board via the MIDI circuit. When the switch is set to the left

position, power is routed to the MIDI In port's pin 1 and pin 2 (refer to page 31 for pin

assignments). If you choose to use another MIDI foot board, be sure to set the switch

to the right to avoid damaging it. If the foot board you are using is designed to handle

phantom power, consult its operating manual to learn how it is wired (that is, which

pins carry its power supply) and what its voltage and current specifications are. If the

voltage and current specifications and wiring match, you may set the switch to the left

to power this foot board via the MIDI cable.

Note that a MIDI foot board may not draw more than 200

milliamperes of current if you want to power it via this port. You must also check and

verify if this MIDI foot board is able to handle 11 volts of alternating current (AC)! If

you are in any doubt, be sure to consult a specialist, meaning an amp technician or

electronics engineer who earns a living with a screwdriver!

Use encoding buttons 1, 2, 3, 4 and 5 to assign the MIDI channel by which the amp will

receive MIDI program change commands and MIDI controller commands addressing

various functions. See the MIDI Controllers table for assignments. Your choices are the

standard 16 MIDI channels numbered from 00 to 15, as well as OMNI mode, where the

amp receives MIDI data sent via any MIDI channel. The following table lists encoding

button settings for specific channels and for OMNI mode.

Encoding button 6's setting controls access to the functions , ,

, , , , , and using fixed MIDI controller

assignments; for the assignment refer to the table "MIDI controller assignment"

printed on the next page.

How to set up encoding button 6 for MIDI controllers: Set the button to ON to enable

specific MIDI controllers to access the assigned amp functions.

Set the button to OFF to bar any MIDI controller from accessing the assigned amp

functions.

When the amp receives a specific MIDI controller command, it has a certain value that

tells the amp what to do. Command values ranging from 0 to 5 deactivate the assigned

function, and values greater than or equal to 5 activate it.

There is one exception is MIDI Controller #7 or #28 and the way it addresses

. MIDI Controller #7 (#28) values from 0 to 5 activate Amp Mute, and values

greater than or equal to 5 reset the amp to the level of the active MASTER volume

control, thereby deactivating Amp Mute.

You cannot disable Amp Mute to activate the amp using a MIDI controller #7

(#28) command when the power amp's Standby switch is engaged. In other words,

you must first flip the Standby switch to control Amp Mute using MIDI commands.

MIDI foot

controller

Tone FX Loop I/II Noise

Gate Hi Gain Lo Mid Hi Mid Master A/B Amp Mute

Amp

Mute

CAUTION:

Please read and heed:

Note:

44 Power Supply For The ENGL Midi Footcontroller

45 Midi Channel & MIDI Controller Enable

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 36 37

Kommentare zu diesen Handbüchern

Keine Kommentare

Engl Steve Morse Signature 100 Betreibershandbuch Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audioverstärker Engl Steve Morse Signature 100