Technical Data
Rated power: approx. 50 watts at 8 or 16 ohms;
Tubes: 4 x ECC 83 / 12AX 7, input-tube (next to the Input jack): FQ selected;
2 x 5881 (6L6 GC) matched set.
Fuses, external: 1,25 AM (medium) at 230 Volts;
2,5 AM (medium) in the 100 and 120 Volts models.
Important: Replace fuses only against same type and rating!
Dimensions: approx. 57,5 x 48 x 27 cm (l x h x d)
Weight: approx. 20 kg
Rear Panel
17 18
17 AC Socket: Connect AC cord here.
CAUTION: Ensure you use an intact AC cord with an insulated plug only!
Before you power the amp up, ensure the voltage value printed beside the
AC socket corresponds to the available current.
18 AC Fuse Box: Contains mains fuse (rear chamber) and spare fuse (front chamber).
NOTE: Ensure replacement fuses bear identical ratings (refer to the table)!
19 Footswitch V.L.S., Reverb: 1/4" stereo jack for double footswitches, executes the following
functions:
1.Switching between the two Master volume levels Hi and Lo (mono terminal)
2.Reverb on/off (stereo terminal).
20 Footswitch Clean / Lead, Lead Boost: 1/4" stereo jack for double footswitches, executes the
following functions:
1.Channel switching between Clean and Lead (mono terminal)
2.Lead Boost (stereo terminal).
21 F.X. Loop Send: Signal output for the Effects loop. Connect this output to a signal processor’s
input/return jack via a shielded cable with 1/4" plugs.
22 F.X. Loop Return: Signal input for the Effects loop. Connect this input to a signal processor’s
output/send jack via a shielded cable with 1/4" plugs.
23 Balance: FX mix control for the Effects loop: Rotate the knob to the Dry position for the pure amp
signal, i.e. no effect on the signal. Turn clockwise to blend in an effect connected to the loop
to the dry signal (parallel/passive). At the Effect position, only the wet signal, i.e. the signal
sent from the FX device is fed to the power amp (serial/passive).
NOTE: If no effects processor is connected to this loop, leave this control in position Dry!
24 Poweramp Output 8 Ohms: Speaker output jack for the internal 12" speaker (type 330,
Screamer 50) or, alternatively an external 8 ohm speaker cabinet. (unplug the internal speaker before
connecting any external cabinet).
25 Poweramp Output 16 Ohms: Speaker output jack for the internal 10" speaker (typ 332, Screamer
pro Blues) or, alternatively an external 16 ohm speaker cabinet. (unplug the internal speakers before
connecting any external cabinet).
NOTE: Never operate the amplifier without a sufficient load, otherwise you may damage or destroy the
power amp! Ensure your cabinet’s specifications match the respective output’s specs.
This amp is designed for the internal speaker(s) or alternatively for one external speaker cabinet (8
or 16 Z). If you decide to connect additional speakers, ensure you keep the overall impedance in
mind! For instance, if you want to connect two external 8 Z systems (or the internal 8 Z speaker
combined with one external 8 Z cabinet), you must first connect them in series and then to the
amp’s 16 Z output. The ENGL Speaker Cabinet Extension (optional) offers a number of options,
right up to four cabinets.
19
20
21 22 23
24
Footswitch
F.X.Loop
Poweramp Output
50 W All-tube
Guitar Combo Amp
Screamer 50;
1x12": Type 330
Screamer pro Blues;
2x10": Type 332
Amp-Design by
Horst Langer
V.L.S.
Reverb
Send Return
8 Ohms
16 Ohms
WIRED FOR:
REPLACE FUSE
ONLY WITH SAME
TYPE AND RATING !
VOLTAGE FUSED
100-120 V
220-240 V
2,5 A
1,25 A
MADE IN GERMANY
DO NOT OPEN !
RISK OF ELECTRIC SHOCK !
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE !
CAUTION !
SERIAL NUMBER:
!
Dry
Effect
Balance
Clea
n/
Lead
Lead Boost
25
(15 Seiten)
(35 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern